JZS14: Tube Front

[cutter67]

« Reply #10 on: 06:40:06 PM / 29-May-08 » Quote 

--------------------------------------------------------------------------------

how do i releive the timing belt tension?




David look how far you have come. do you remember asking that question? look at what you are doing now very impressive

[David B]

Now I'm a Toyota/Lexus tech lol
Life is cray
I swap out timing belts like errday

[David B]

mounts came in,


turns out they dont fit 100 percent, on the passenger side mount 2 of the holes didnt line up so i had to redrill one, and slot the other to make it fit.. the transmission mount might need some modification too from what i can see.. WHATEVER.. made it work.

some pics of the install, brings me a smile, im the dude on the left with the blue shirt. had some friends come over to avoid scratching shit up.







i had to put 2 hockey pucks in between the mounts and the subframe for a good fit

[I_heart_VVL]

bahahaha hockey puck motor mounts are so boss.
just make sure to check em every now and then.

[David B]

bahahaha hockey puck motor mounts are so boss.
just make sure to check em every now and then.

i might end up using normal mounts, idk yet
Post Merge: 08:39:35 PM / 14-May-12 made my trans mount solid, didnt have a rubber mount anyways



need to measure and take my 1j s12 driveshaft back to driveline to mate with the stock rear s14 2 piece


great rad clearance (ka koyo), will be making a aluminum shroud & fan setup


shifter extension puts it right where i need it, sweet


ill start mocking the piping up when i find or buy a kit to mock up

[David B]

bay is pretty much done minus the piping needs to be redone & so does the intake




race car trash lol


side view


relocated fusebox, still in the process of bringing the headlight wiring back to the headlights, this gives me room for a intake on the other side from where i had it down where the stock battery goes




using my in house, lol.. steel fan shroud for a bit until i get some money right, this time though a koyo radiator and sealing all the seams will give me some better cooling action, i sealed the fans to the shroud also.. ive got a 61.C mishimoto thermostat also


heres my intake for now, if i have leftover piping after i redo the i/c piping ill do this in aluminum





LIKE!! on nexen @ facebook i need tires for hyperfest toyota treats me poorly in pay
me drifting my DD at ods a few weeks ago

http://www.facebook.com/NEXENTIRE

[David B]

turns out the flange i used on my s12 is the same as the flange on my rear stock driveshaft piece


measured 22 inches from the output shaft to driveshaft flange, dropped all the pieces off @ driveline today, ill have it driving in 2 days when i get it back!

swap all together 100 percent minus the driveshaft, ill be redoing the piping again later, i just need to distribute funds towards other things atm



made a downpipe to mate up with the exhaust that came with a car


clearance is swell, all above the frame rails




startup vid
http://www.youtube.com/watch?v=iYdv7LqTkjI&feature=g-upl

[CamInHead]

That's just pure filth! 

[tommy]

Looks like you cleaned the slag from inside the pipe...

[David B]

i cant wait to get a seat in this bitch!! next on my list, gotta get a in date seat &  harness for tech inspection @ hyperfest

[Prolowtone]

Sick!, love your builds David. Keep up the good work

[sideways_s12]

sounds sexy as fuck makes me want to do a 2jz swap...

[David B]

JZ 4 life

now it officially drives! but ive got the the patience to wait & finish some more wiring etc before i go dumping clutch,
lost my shifter bushing? gotta order another one at work/toyota,
need to wire up that aem wideband pictured,
need to reroute the alt wiring through the cutoff switch, the killswitch isnt turning the car off ...
figure out how to use the stock tach if i can, would be nice
order and install a coolant temp sensor/guage
buy a seat, make seat rails, install seat
aquire RL overfender (most likley buying a pair)
yadda yadda more things on a big list ive got in my head


Post Merge: 08:33:34 PM / 24-May-12 got some 25 mm spacers for the front
got the wrong thread pitch studs XD


just orderd some 240 ones at work & pressed em in, the front studs fit, rears dont due to a slim shank



some sr20 s12 coupe progress

[David B]

finally got it off the stands & drove it out of the garage, it sounds & looks so good.. Im so excited to drift a car like this finally . Ive only drifted a KA S14 a long time ago..
ill be driving it at hyperfest june 16th if i qualify, & also driving the 17th @ Drift Nirvana. pumped!

pics of it outside letting it run, ill get more footage later..







still have tons to do! borrow a in date seat soon thats next, a battery box, gotta wire the wipers, & other things for tech!

[Prolowtone]

Sexy, Engine bay actually looks quite clean.

[David B]

[night_s12]

Sounds super sexy man cant wait to see some footage of it sliding arou d

[David B]

me either!

[cutter67]

cant wait to see you drift on the 16th and 17th

[nismo_200sx]

fml holy fuck i fucking suck giant ass i seriously need to sell my s12 and get out of cars because of this thread. it takes me damn near a month to figure out my oil feed line on my cadet and you swap a jz in within a week or so. you are so fucking magical that the tooth fairy gets pregnant everytime you touch a car. shit lol im super jelly