Club-S12 International S12OC United Kingdom ClubS12 France S12Silvia Australia S12.org.ua Eastern Europe S12 of Sweden S12 Japan BBS
Please login or register.

Login with username, password and session length

Author Topic: It's been a long time, but Project SE Resurrection has begun!  (Read 901 times)

Online rednucleus

  • Old Fart #2
  • CONTRIBUTING MEMBER
  • Sr. Member
  • *****
  • Location: Marysville, WA
  • Posts: 1,985
  • Vehicle: 1985 Nissan 200SX
Re: It's been a long time, but Project SE Resurrection has begun!
« Reply #20 on: 06:23:10 PM / 14-Feb-17 »
Start with a gallon of Diesel and slosh that around a couple times a day for a week.  Might not need anything else after that.

Offline cls12vg30

  • Honored Veterans
  • S12 Guru
  • *****
  • Location: Raleigh, North Carolina, USA
  • Posts: 4,006
  • Vehicle: 1988 Nissan 200SX
    • http://www.v6-s12.com
Re: It's been a long time, but Project SE Resurrection has begun!
« Reply #21 on: 02:33:41 PM / 27-Feb-17 »
Removed fuel tank, added a gallon of Evapo-Rust, and let it work for 24 hours, flipping the tank every hour (except while sleeping).  Looking at the inside of the tank, I'm comfortable giving it a shot.  Now I need a fuel pump and a new O-ring for the fuel pump housing.  I see a lot of people have had good luck with Walbro pumps.  I'll probably go that route.  I see on the Walbro site they don't have an option for 200SX's other than B14's.  Am I wrong in assuming the Z31 pump is the same?
« Last Edit: 02:36:59 PM / 27-Feb-17 by cls12vg30 »
1988 200SX SE V6
2015 Jeep Renegade 1.4T


Online Wonderingraven

  • The Ninja
  • Sr. Member
  • ****
  • Location: Las Vegas, NV
  • Posts: 1,698
  • Vehicle: 1987 Nissan 200SX
  • The Drift Ninja
    • GFunk Garage
Re: It's been a long time, but Project SE Resurrection has begun!
« Reply #22 on: 03:41:29 PM / 27-Feb-17 »
Removed fuel tank, added a gallon of Evapo-Rust, and let it work for 24 hours, flipping the tank every hour (except while sleeping).  Looking at the inside of the tank, I'm comfortable giving it a shot.  Now I need a fuel pump and a new O-ring for the fuel pump housing.  I see a lot of people have had good luck with Walbro pumps.  I'll probably go that route.  I see on the Walbro site they don't have an option for 200SX's other than B14's.  Am I wrong in assuming the Z31 pump is the same?

I am using one for a 240sx and it wires in just fine just have to secure it into the old pump location as they are  bit smaller, but has been solid on my sev6.
1987 - Project: Fairlady Silvia
1986 - Project: Serenity
1986 - Project: Dread Pirate Robin
{Blogged builds} www.g-funk.net/blog/

Offline cls12vg30

  • Honored Veterans
  • S12 Guru
  • *****
  • Location: Raleigh, North Carolina, USA
  • Posts: 4,006
  • Vehicle: 1988 Nissan 200SX
    • http://www.v6-s12.com
Re: It's been a long time, but Project SE Resurrection has begun!
« Reply #23 on: 02:39:29 PM / 28-Feb-17 »
I am using one for a 240sx and it wires in just fine just have to secure it into the old pump location as they are  bit smaller, but has been solid on my sev6.

Thanks for the tip.  Walbro shows the same part# for S13 and Z31, so that looks like the one.
1988 200SX SE V6
2015 Jeep Renegade 1.4T