Club-S12 International S12OC United Kingdom ClubS12 France S12Silvia Australia S12.org.ua Eastern Europe S12 of Sweden S12 Japan BBS
Please login or register.

Login with username, password and session length

Author Topic: Project: Excalibur Prime - 1987 200sx SEv6...  (Read 113017 times)

Offline Wonderingraven

  • The Drift Ninja
  • CONTRIBUTING MEMBER
  • Sr. Member
  • *****
  • Location: Las Vegas, NV
  • Posts: 1,822
  • Vehicle: 1987 Nissan 200SX
  • The Drift Ninja
    • WRnet
Re: Project: Excalibur Prime - 1987 200sx SEv6...
« Reply #820 on: 03:45:45 PM / 26-Oct-19 »
currently hunting down an transmission to go with it.

So far this is what I've found the motor bottom half mounts up, I suspect that the exhaust driver side will interfere with the steering column.
Currently also trying to get this s130 out of my garage, it's almost done to an initial fireup. Just working 10-12hours isn't helping either.
Hacker | Streamer | Gamer | Drifter
1987 - Project: Excalibur Prime
1986 - Project: Serenity

Offline Wonderingraven

  • The Drift Ninja
  • CONTRIBUTING MEMBER
  • Sr. Member
  • *****
  • Location: Las Vegas, NV
  • Posts: 1,822
  • Vehicle: 1987 Nissan 200SX
  • The Drift Ninja
    • WRnet
Re: Project: Excalibur Prime - 1987 200sx SEv6...
« Reply #821 on: 01:27:03 PM / 30-Jan-20 »
I might be retiring this project all together.
Couple of reasons:

1) I am acquiring another project s12 coupe tho, I am going to be dropping an ca18det into it. So all my time is going into this project.
2)  Emotionally, it wouldn't be as bad as it is now, that if my mom didn't pass away a few days after I blew up the motor going sideways at the track and the lack of local support I kinda gave up with motivation of keeping this one alive.


Hacker | Streamer | Gamer | Drifter
1987 - Project: Excalibur Prime
1986 - Project: Serenity

Offline CzechSilvia

Re: Project: Excalibur Prime - 1987 200sx SEv6...
« Reply #822 on: 03:57:48 PM / 30-Jan-20 »
That's a real shame, but hey, at least the engine died the warrior's death, that's the way it should be and not letting them rust out in some shed. And if you sell the shell, make sure to sell it to someone who'll appretiate it. Also - looking forward to the ca18det project!
But what do I know? All I know about cars I learned from youtube...

Offline Wonderingraven

  • The Drift Ninja
  • CONTRIBUTING MEMBER
  • Sr. Member
  • *****
  • Location: Las Vegas, NV
  • Posts: 1,822
  • Vehicle: 1987 Nissan 200SX
  • The Drift Ninja
    • WRnet
Re: Project: Excalibur Prime - 1987 200sx SEv6...
« Reply #823 on: 10:20:58 PM / 02-Mar-20 »
Well, I have a solution for the s12, seems that I had some friends reaching out and giving me some inspiration and support lately. TBH, I can use all I can get... it's hard.

I have a VG30DE from an Infiniti J30 sitting in my garage.
I now have an CD009 (z33 transmission) ready to be mated with an VG30DE Auto bell housing with internal slave setup from JWT.
 
This might get interesting soon!

I've been thinking of doing this customization live streaming but unsure yet how this will go down.
« Last Edit: 06:29:44 PM / 03-Mar-20 by Wonderingraven »
Hacker | Streamer | Gamer | Drifter
1987 - Project: Excalibur Prime
1986 - Project: Serenity

Offline rednucleus

  • Old Fart #2
  • CONTRIBUTING MEMBER
  • Sr. Member
  • *****
  • Location: Marysville, WA
  • Posts: 2,056
  • Vehicle: 1985 Nissan 200SX
Re: Project: Excalibur Prime - 1987 200sx SEv6...
« Reply #824 on: 04:11:50 PM / 03-Mar-20 »
So many letters & numbers, so little time!

Offline Wonderingraven

  • The Drift Ninja
  • CONTRIBUTING MEMBER
  • Sr. Member
  • *****
  • Location: Las Vegas, NV
  • Posts: 1,822
  • Vehicle: 1987 Nissan 200SX
  • The Drift Ninja
    • WRnet
Re: Project: Excalibur Prime - 1987 200sx SEv6...
« Reply #825 on: 05:22:13 PM / 08-Mar-20 »
Acquired an Z33 transmission with a J30 Autotrans.



Pairing up with this motor here.


FYI, this is what I will be doing, and converting this to an internal slave cyl.
https://youtu.be/Z6ETCVJN2mU

Parts will be utilizing with this:
http://jimwolftechnology.com/customer_part_detail.asp?PartID=539

with.
http://jimwolftechnology.com/customer_part_detail.asp?PartID=560
http://jimwolftechnology.com/customer_part_detail.asp?PartID=565


Hacker | Streamer | Gamer | Drifter
1987 - Project: Excalibur Prime
1986 - Project: Serenity

Offline Wonderingraven

  • The Drift Ninja
  • CONTRIBUTING MEMBER
  • Sr. Member
  • *****
  • Location: Las Vegas, NV
  • Posts: 1,822
  • Vehicle: 1987 Nissan 200SX
  • The Drift Ninja
    • WRnet
Re: Project: Excalibur Prime - 1987 200sx SEv6...
« Reply #826 on: 05:29:54 PM / 19-Mar-20 »
it is done, motor is finally out and the preparations is now underway.
Hacker | Streamer | Gamer | Drifter
1987 - Project: Excalibur Prime
1986 - Project: Serenity

Offline iceageg

  • Full Member
  • ***
  • Location: Denver, CO
  • Posts: 638
Re: Project: Excalibur Prime - 1987 200sx SEv6...
« Reply #827 on: 07:37:27 AM / 20-Mar-20 »
Making good use of your mandatory stay home time.  Good on you.
I was afraid all the five gallon buckets of pain stacked four high were going to fall over

Offline Wonderingraven

  • The Drift Ninja
  • CONTRIBUTING MEMBER
  • Sr. Member
  • *****
  • Location: Las Vegas, NV
  • Posts: 1,822
  • Vehicle: 1987 Nissan 200SX
  • The Drift Ninja
    • WRnet
Re: Project: Excalibur Prime - 1987 200sx SEv6...
« Reply #828 on: 11:38:42 AM / 20-Mar-20 »
I am assuming there isn't a huge write up on this. wiring is similar to wiring the rb25 almost to a T and when I clean up my notes I'll post the wiring guide and with that said I am going to do an in-depth write up on this process including the whole VG30DE Auto bellhousing on an Z33 CD09 transmission and how it fits in.

As of now I got no job for 30 days sooo here we go nose diving into this project.

The before


Pulling the engine.



the engine tare down.

Hacker | Streamer | Gamer | Drifter
1987 - Project: Excalibur Prime
1986 - Project: Serenity

Offline Wonderingraven

  • The Drift Ninja
  • CONTRIBUTING MEMBER
  • Sr. Member
  • *****
  • Location: Las Vegas, NV
  • Posts: 1,822
  • Vehicle: 1987 Nissan 200SX
  • The Drift Ninja
    • WRnet
Re: Project: Excalibur Prime - 1987 200sx SEv6...
« Reply #829 on: 01:08:39 AM / 28-Mar-20 »
quick update, motor is ready to drop in. I'll add pictures to this check back later.

I can use either SEv6 sohc exhaust headers (have to modify the holes for the studs just a little wider and oval out the insides) but they can fit right in with no other issues.
The J30 exhaust looks like it will fit, I would have to modify the Y pipe to  compensate the extra length from the headers and match how they bolt up.

JWT is shipping out everything monday that I need to fit in the transmission (minus the shifter, as I need someone to cut and make the bracket shorter)

Last but not least, I need to get my driveshaft made when this is ready.

Then I can move onto wiring.
« Last Edit: 01:09:00 AM / 28-Mar-20 by Wonderingraven »
Hacker | Streamer | Gamer | Drifter
1987 - Project: Excalibur Prime
1986 - Project: Serenity