Definite Weld On Coilover Parts List For s12 suspension

[Wonderingraven]

That I do not know, I think it's for the best performance for the mod, it's recommended AGX.

[Jordan]

I will be doing this over the summer. Hoping to start gathering parts over the next couple months. I need to know what the max height is that can be achieved with this setup. I need to have my car higher for winter driving and parking lots. I do want the adjustable setup.

[sam31183]

Technically you can raise it up and down the full length of the sleeves...from the looks of it you could definitely have a 4x4 ride height if you wanted to for snow or like rallyx. Besides rubbing all the time I am pretty happy with my set ride height so I haven't messed with it...i might get some lolz though after seeing my car way up in the air.

[Jordan]

That sounds like there's plenty of adjustment. What's causing the rubbing?

[sam31183]

Speedbumps and dips and shit. :p

[Unleashedrb200sx]

a friend of mine just bought an 84 (solid axle) i just want to know if the bc suspension kit would fit with an s13 front convertion   the most important of the question is would the rear setup fit ???
Post Merge: 08:16:43 AM / 07-Jan-12
bump

[zilvia_brothers]

Whats spring rate are you guys you using for DD. i usually like driving stiff but too much to hurt my back

[silverton]

FRONT:
ROLL CENTER ADJUSTERS- https://technotoytuning.com/nissan/s130/roll-center-adjusters-datsun-280zx
S13 CAMBERPLATES- https://technotoytuning.com/nissan/s13/camber-plates-nissan-s13
280ZX GC SLEEVES- https://technotoytuning.com/nissan/s130/front-ground-control-weld-coilover-kit-datsun-280zx
MR2 SHOCKS- KYB AGX 765015

REAR:
SPRING PERCH [MUST USE SS-85500-A]- http://www.daymotorsports.com/product/352/SPRING-SPACERS
SPRINGS [MUST USE 5"X8" SPRING]- http://www.daymotorsports.com/product/389/FRONT-COIL-SPRINGS
FOXBODY SHOCKS- KYB AGX 743021

Me updating this with fresh links, as the OP links are dead and never "rendered" correctly, should let you know I'm up to something... though, I'm probably not going to end up using any of these parts. LOL

[Dr.Steels]

Found what I was looking for

[Ju_S12_Turbo]

FYI Day Motor sports still sells the SSS springs (Cheaper shipping and stuff as well) they just moved the url, For "Front springs (Minimum 550 lbs and max 850lbs)  " http://www.daymotorsports.com/proddisp.php?ln=14667  And for "Rear springs (Minimum 100 lbs Max 400lbs) http://www.daymotorsports.com/proddisp.php?ln=14828

[420-86notch]

would these springs work on oem front shock tubes and the stock rear perches

[seishuku]

Quick question:
How much travel do the Eibach springs offer, compared to OEM strut/spring setup?

I ask, because looking at the springs that come with the T3 weld-on kit, it looks like it seriously limits the suspension travel.

Unless I can order taller springs when I order the kit?

[Arro]

Once you sleeve it, Eibach will make you whatever spring you want in whatever spec you want, both rate and dimensions.

[Basic]

so, reading through this thread, i had a question on how adjustable the right height is, specifically for the rear. I understand this depends on what spring rate you run, but assuming you run something that's a typical daily spring rate (maybe 400 lb/in) for the rear - what kind of height adjustment can you expect? I want a slightly lower than stock height, the springs that are on my car now are too low and making the rear camber really wonky.