Club-S12 International S12OC United Kingdom ClubS12 France S12Silvia Australia S12.org.ua Eastern Europe S12 of Sweden S12 Japan BBS
Please login or register.

Login with username, password and session length

Author Topic: Ever Rebuild a Starter?  (Read 1361 times)

Offline rednucleus

  • Old Fart #2
  • CONTRIBUTING MEMBER
  • Sr. Member
  • *****
  • Location: Marysville, WA
  • Posts: 2,044
  • Vehicle: 1985 Nissan 200SX
Ever Rebuild a Starter?
« on: 03:44:02 PM / 10-Jun-15 »
My original starter (30 yrs old, not bad Nissan) has started acting up - where you get no starter when turning the key until you tap it with a hammer. Got one ordered from Rockauto ($75 shipped) but also see there are brush sets available.  Opened mine up and found brushes are at least 75% gone, so springs barely touch them leading to intermittent starts.  The rest of the internals look fine; just dirty. Found several videos showing cleaning and brush replacement. Going to try it just for fun and it will give me a spare starter too. Brushes cost under $15 for a set of four. Pics for a how to coming soon! Some would say it's a waste of time and I'm cheap (2nd part definitely true), but this old guy hates to throw stuff out that can be easily fixed and returned to use. Maybe that's why I still have the S12?

Facebook Share    


Offline sideways_s12

  • CS12 OG
  • Moderators
  • S12 Guru
  • *****
  • Location: Las Vegas NV
  • Posts: 11,013
  • Vehicle: 1987 Nissan 200SX
  • Quit Fuckin around and start the car!
Re: Ever Rebuild a Starter?
« Reply #1 on: 05:19:36 PM / 10-Jun-15 »
If you can rebuild it got nuts. I just took my starter to the local auto parts store and they rebuilt for half the cost of a new one... but if rebuilding it yourself is even cheaper and if its easy, I'd go that route ....

Offline weitrhino

  • Full Member
  • ***
  • Location: North Texas
  • Posts: 477
  • Vehicle: 1985 Nissan 200SX
  • '85 Notch just cracked 40k miles! RIP '86 Notch
    • Blue Mouth Promotions LLC
Re: Ever Rebuild a Starter?
« Reply #2 on: 08:02:32 PM / 10-Jun-15 »
This would be right up my diy alley. I would definitely attempt to rebuild it myself especially if the correct brush set is available. $15 worth of risk is nothing in the grand scheme of things.  I did a similar rebuild of an alternator on my old 86 coupe many years ago when the rectifier fried and have rebuilt a few power drills.

Go for it!

Offline iceageg

  • Full Member
  • ***
  • Location: Denver, CO
  • Posts: 623
Re: Ever Rebuild a Starter?
« Reply #3 on: 09:24:18 AM / 11-Jun-15 »
Rebuilt the starter in our 92 pathfinder a few years back.  It has worked perfect ever since.  Doubt I will ever buy one again without at least trying to rebuild.  All-n-all it was pretty easy.  As with anything make sure you keep the parts in order for re-assembly and mark things for alignment before you pull them apart.

A can of electric contact cleaner is nice to have on hand for this project too.  Awesome stuff.
I was afraid all the five gallon buckets of pain stacked four high were going to fall over

Offline Cajun1guy

  • Old fart (pedoro numero uno)
  • Full Member
  • ***
  • Location: Mandeville, Lousyana
  • Posts: 758
  • Vehicle: 1984 Nissan 200SX
Re: Ever Rebuild a Starter?
« Reply #4 on: 05:15:44 PM / 19-Jun-15 »
Indeed, do it and post the process. I hate to replace those buggars, getting harder to locally source and more costly all the time. I scared the heck out of myself a few years back when mine was acting up. I found a CARQUEST that had one, so I went over and left the car running so I wouldn't have to start it again. When I came out the temp was almost pegged out, seems that my electric fan thermostat was not set right and it almost did me in. Radiator failed not too long after that, thank God for OEM-Surplus!